Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Blog Article
The content down below relating to Tools You Need to Install a New Bathtub is particularly insightful. Have a go and draw your own personal assumptions.
Setting up a tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, and in some cases, tiling abilities. Changing an old bath tub with a brand-new one is additionally a moderately tough job. If the old bathtub is easily obtainable, the task can move immediately; if you need to open a wall to eliminate the old bathtub as well as position the new bathtub, the task is a lot harder. In either instance, the task is within a house handyman's skills, although you will need a helper to leave the old bathtub as well as set in the brand-new one. Make certain you have qualified on your own for the task and fit trying it. Rather than working with a service provider to take over a halfway-completed project, it is far better to take into consideration utilizing one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This short article will certainly assist you install a new bath tub in your restroom if you have actually already purchased a brand-new tub as well as don't need to transform the setup of your previous supply of water pipelines.
Your devices and material list need to make up the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, then the first thing you ought to do is detach the supply of water. After doing so, switch on the taps to drain any water staying in the system. The process of eliminating the existing taps can be quite bothersome as a result of the limited gain access to that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a cloth ready for the continuing to be water that will come from the pipes. Once the supply pipelines have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will have to be cleaned of any type of old sealing substance.
Prior to carrying on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washing machines remain in area in between the faucet and the sink. Protect the faucet in place with the producer given backnut. Once the tap is firmly in position, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet connectors. The previous type should be linked to the tap finishes first, tightening up only by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bath tub
Using the two wood boards under its feet, put the bath tub in the required setting. The wood boards are valuable in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Switch on the supply of water and check all joints and new pipework for leakages as well as tighten them if needed. Fill the bathtub as well as likewise check the overflow electrical outlet and also the typical outlet for leakages.
Finally, fix the bath paneling as explained in the maker's user's manual. Tiling and also sealing around the bath tub must wait until the bath tub has been made use of a minimum of once as this will certainly settle it right into its last setting.
Preparing for the Setup
Firstly, the supporting structure supplied with the bathroom ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop stress on the tub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should now prepare to be suited its final setting.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack an inflexible seal, triggering the water to pass through the wall in between the bath and also the tiling, causing complications with dampness and also possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and installations. They are sold in tubes as well as cartridges, and also can sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of drenched newspaper or soft rope. Remember to constantly load the tub with water before securing, to permit the motion experienced when the tub is in usage. The sealer can break fairly very early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly readily available on the market. It is advisable to fit the ceramic tiles using water-resistant or water-proof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
I was made aware of that editorial about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through a good friend on a different blog. Sharing is good. You won't know, you may very well be doing someone a favor. Kudos for your time. Come back soon.
Don't settle; choose expert plumbers. Report this page